|
02-24-2013, 03:45 PM
|
#1
|
Member
Join Date: Sep 2009
Posts: 53
|
convection/micro combo models and venting
We're replacing our microwave with a convection/micro combo of equal or larger size. Looking for advice on models and venting.
PIExpress
__________________
__________________
1980 Newell Coach
|
|
|
02-24-2013, 04:49 PM
|
#2
|
Senior Member
Join Date: Mar 2008
Location: Forest Ranch, Ca for the summer
Posts: 299
|
From my experience, you'll want a countertop unit with a venting kit that vents thru the front of the unit. The venting kits are pricy, but are required when a unit is put in an unvented area.
I just installed a Sears 721.679?. It replaced an existing Amana unit I installed some years ago, and used the same venting kit.
After I installed the new unit, I had a chance to look at the old one to see what the noise was. The set screw on the fan for the convection heating element had backed out & allowed the fan to rub on the case. Oh well only $324 down the drain.
I do quite a bit of cooking & baking & this is the best unit for it's cost.
I got it on Ebay out of Texas.
__________________
__________________
Gordon Hummel
1991 41.5' #266
8v92
2009 Pontiac Vibe GT Toad
Fulltime on the road
|
|
|
02-24-2013, 05:43 PM
|
#3
|
Senior Member
Join Date: Mar 2008
Location: Forest Ranch, Ca for the summer
Posts: 299
|
Microwave install
I've just added a few pictures of the microwave installed. The existing cabinet size was ok, but the black switch plate above it had to be cut down in height & also moved out to overlap the top of the new front panel. Also had to add a little spacer on the left, top & right. I usually won't make any changes unless it will look factory.
On my switch panel be careful as there is 110 ac to the water heater switch. Also the top of the new microwave bezel will have to be notched to allow the generator switch to fit. Also you'll want to add some electrical tape to the cut out you made, as I have found you might start the generator by mistake by touching the switch to the alum bezel !
__________________
Gordon Hummel
1991 41.5' #266
8v92
2009 Pontiac Vibe GT Toad
Fulltime on the road
|
|
|
02-24-2013, 06:10 PM
|
#4
|
Member
Join Date: Sep 2009
Posts: 53
|
Gordon,
What brand is your convection Microwave and how much time did it take for you to complete installation?
__________________
1980 Newell Coach
|
|
|
02-24-2013, 06:27 PM
|
#5
|
Senior Member
Join Date: Jan 2003
Location: Heartland
Posts: 3,563
|
Gordon, that is a pretty sanitary job. Great pointer regarding the gen switch. How did you come up with the stainless trim, was it already existing or did you buy a trim kit??
__________________
Ken
Previous Owner of 3 Newell's
Wanted: Newell Coach Needing Engine Replacement!
If you want to sell, PM or Private Message me. Thanks!
"I know I’m not perfect, and I don't live to be. But before you start pointing fingers, make sure your hands are clean."
-Bob Marley
|
|
|
02-24-2013, 06:53 PM
|
#6
|
Senior Member
Join Date: Mar 2008
Location: Forest Ranch, Ca for the summer
Posts: 299
|
The Ebay listing is below for the unit I purchased. You will still need the venting kit, that adds about +/- 2" in height. The kit includes the front bezel & a top & bottom vent that provides intake on the top & exhaust on the bottom; as these are normally done on the back of a countertop unit.
As to how much time to complete, I depends of your existing cabinet space & your abilities. As an example, I was concerned with the bottom of the front bezel lining up with the bottom of original cabinet. I installed the top & bottom vents on the microwave & slid it in. To my surprize when I held the bezel up in place, the bottom lined up perfectly. If the bottom of the bezel was below the cabinet I could just raise it, maybe if I had the room. If the bezel had been above the bottom of the cabinet & I didn't like what it looked like, I may have had to replace a lot of formica covered wood. It all depends on the look you are trying to achieve.
I think I had to move the plug in back up a little, but that was about it.
New Kenmore Elite Stainless 1 5 CU ft Convection Countertop Microwave Oven 67903 | eBay
__________________
Gordon Hummel
1991 41.5' #266
8v92
2009 Pontiac Vibe GT Toad
Fulltime on the road
|
|
|
02-24-2013, 08:04 PM
|
#8
|
Senior Member
Join Date: Jan 2003
Location: Heartland
Posts: 3,563
|
I don't see where the trim kit is included with either one? Maybe I'm missing it? I do see some different trim kits by different manufactures and I'm sure many different configurations will work. Just, need to make some different measurements and play around with what works as well for the opening. All volunteers please stand up!
I found the following trim kit looks just like Gordon's in a 27" size. Link Below:
Panasonic Optional 27" Trim Kit for 1.2 cuft Microwaves, Stainless Steel, NN-TK621SS
Panasonic 27-Inch Trim Kit for 1.5 cuft Panasonic Stainless Convection Microwave Ovens, NN-TK903S
__________________
Ken
Previous Owner of 3 Newell's
Wanted: Newell Coach Needing Engine Replacement!
If you want to sell, PM or Private Message me. Thanks!
"I know I’m not perfect, and I don't live to be. But before you start pointing fingers, make sure your hands are clean."
-Bob Marley
|
|
|
02-24-2013, 08:25 PM
|
#9
|
Senior Member
Join Date: Jan 2003
Location: Heartland
Posts: 3,563
|
I also found these two links for a 1.5 cubic inch models below:
<iframe src="http://rcm.amazon.com/e/cm?t=affiliatechie-20&o=1&p=8&l=as1&asins=B00133NVOK&ref=qf_sp_asin_t il&fc1=000000&IS2=1<1=_blank&m=amazon&lc1=0000FF &bc1=FFFFFF&bg1=FFFFFF&f=ifr" style="width:120px;height:240px;" marginwidth="0" marginheight="0" frameborder="0" scrolling="no"></iframe>
<iframe src="http://rcm.amazon.com/e/cm?t=affiliatechie-20&o=1&p=8&l=as1&asins=B000UW3N98&ref=qf_sp_asin_t il&fc1=000000&IS2=1<1=_blank&m=amazon&lc1=0000FF &bc1=FFFFFF&bg1=FFFFFF&f=ifr" style="width:120px;height:240px;" marginwidth="0" marginheight="0" frameborder="0" scrolling="no"></iframe>
__________________
Ken
Previous Owner of 3 Newell's
Wanted: Newell Coach Needing Engine Replacement!
If you want to sell, PM or Private Message me. Thanks!
"I know I’m not perfect, and I don't live to be. But before you start pointing fingers, make sure your hands are clean."
-Bob Marley
|
|
|
02-24-2013, 09:09 PM
|
#10
|
Senior Member
Join Date: Mar 2008
Location: Forest Ranch, Ca for the summer
Posts: 299
|
The Amazon price is much better, but neither will come with the vent kit. I went to the sears site & 67903 is not a current model. They have a 67909 & list a built in kit for but it is only the front bezel? My original unit was a Amana but absolutely identical. As I recall it took me a while to get the vent kit, as the Amana at that time was discontinued.
The vent kit is MANDATORY......in my opinion!
I guess if you put in where the old one was & cut some venting holes in the bottom & then ran the roof vent fan above it, it might work.
These trim kits are like the razor blade business; they give you the microwave & make their money on the install kit.
If you look at units that are wall mounted for over the stove use, they are more expensive, smaller size. Not sure if I would hang it on any motorhome wall!
I'm going up the hill later to where my old amana is & see if I saved the vent kit mounting instructions & maybe some pictures.
__________________
Gordon Hummel
1991 41.5' #266
8v92
2009 Pontiac Vibe GT Toad
Fulltime on the road
|
|
|
02-28-2013, 04:03 AM
|
#12
|
Member
Join Date: Dec 2011
Posts: 52
|
|
|
|
02-28-2013, 03:47 PM
|
#13
|
Senior Member
Join Date: Jan 2003
Location: Heartland
Posts: 3,563
|
TheCarabiners, you folks did some cutting didn't you? Thank you for sharing, this just shows you that you can make alterations for pretty much anything you may need in your coach. In fact It wouldn't be all that hard for most to reshape or alter an area to fill in or fit the new appliance or what have you. Just some creativity like it took the factory to bring out the uniqueness's in these wonderful coaches.
Exited to see more upgrades from these folks. They already have a beautiful paint job and I know many other interior improvements are being done. Share, share, share!
__________________
__________________
Ken
Previous Owner of 3 Newell's
Wanted: Newell Coach Needing Engine Replacement!
If you want to sell, PM or Private Message me. Thanks!
"I know I’m not perfect, and I don't live to be. But before you start pointing fingers, make sure your hands are clean."
-Bob Marley
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|