|
12-28-2012, 04:55 PM
|
#1
|
Member
Join Date: Nov 2012
Posts: 73
|
Power Cord Heating Up Common Problem?
We've recently purchased a used Newell Coach and have a few things to work on.
The most worrisome is the very warm power cord that heats up when the AC is on. It only heats up at the plug and the first 6 inches of the cord so there is some resistance building up there. We are talking hot to the touch, like
I've cleaned the plug prongs but there is not much else to do.
I'm considering cutting the cord back about 12 inches and re splicing a new plug on as I'm guessing the old plug is a bit worn from years of use and may have some damaged wires thus causing the resistance to go up.
Is this a common problem?
Thanks,
Cliff
__________________
__________________
Cliff Robinson
1976 Newell Coach W/Cummins Engine
|
|
|
12-28-2012, 05:12 PM
|
#2
|
Senior Member
Join Date: May 2012
Location: Boise Idaho
Posts: 719
|
A power cord that is hot to the touch is not a common problem. Either the AC unit is drawing more amps that it is supposed to (indicating it requires servicing) or the power cord is not sized correctly. There are charts available on the Internet that will tell you what gauge wires you should have based on length and amps.
__________________
__________________
Jon & Chris Everton
1986 40' Dog House #86
0 hp 8V92 Allison HT740
Soon to be 500hp ISM with ZF 6 Speed
|
|
|
12-28-2012, 05:34 PM
|
#3
|
Senior Member
Join Date: Nov 2010
Location: greensboro,nc
Posts: 111
|
I had one last year that was a moulded plug and it got so hot I had to turn off the breaker to let it cool before I pulled it out out the recepticle,I replaced it and the new one stays cool.
__________________
2008 Liberty XLII
|
|
|
12-28-2012, 06:15 PM
|
#4
|
Senior Member
Join Date: Aug 2012
Posts: 130
|
One thing that can happen with a power cord, especially if the plug is not of the molded type, is that water and other contaminates can enter the end of the wire and "Wick" up into the cord causing corrosion... I've seen it as much as a foot or more of corrosion on some wires I've checked.
I would cut back till you get good shiny copper and put on a new plug, seal it well using liquid electrical tape after assembly (You don't want that on the screws) and keep it clean and dry.
Many times motor coach power cords are left lying on the ground, the plug is plugged into an extension cord and left lying on the ground, it rains, a puddle forms and the plug (and the outlet end of the extension cord) are left under water. RV cords are not designed for this kind of abuse (Marine cords are, but a marine plug is over $100, and that is just the plug)
__________________
Ernest Jenkins
2005 Newell Thunder
Shakin the open road!
|
|
|
12-28-2012, 11:38 PM
|
#5
|
Senior Member
Join Date: Dec 2005
Location: Southern California
Posts: 1,018
|
Sounds like Ernest's & the others recommendations would solve your problem. Good to know if I ever have that issue.
Joseph
__________________
1976 Newell Classic (Sold)
Home Base: Riverside, CA
If anyone needs my contact info private message me and I will send it to you.
-Joseph-
|
|
|
12-29-2012, 06:29 AM
|
#6
|
Senior Member
Join Date: Dec 2007
Location: Armenia, Wisconsin
Posts: 278
|
There is one thing to do -- replace the cord. You are dealing with a 50 amp 120VAC circuit exposed to the weather in use. Get a new, molded cord from an parts supply and use it to replace your old cord. If you use an extension cord with the coupling out in the weather, seal it with tape and prop it off the ground.
A general caution: The prongs of a shore power cord can get oxidized by plugging it into a live circuit. RV 120VAC circuits are always under load -- from the battery charger if nothing else. When you plug in the cord to a live circuit, the load will cause arcing and oxidize the prongs. Every campground I have been in has a circuit breaker controlling the outlets at the site box. Trip the breaker off before you plug and when you unplug.
Phil
__________________
1983 Newell Coach
|
|
|
12-29-2012, 02:52 PM
|
#7
|
Member
Join Date: Aug 2012
Posts: 33
|
If your power source (that your cord is plugged into) doesn't have enough amperage it will cause it to heat up. There may not be a problem with your shore line. If you are plugged into a regular outlet in your home it will be a 15A or 20A outlet.
__________________
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|