Remove and Install EXHAUST MANIFOLD (Water-Cooled) Detroit Diesel 92 Series Engine - Luxury Coach Lifestyles
Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
Reply
 
Thread Tools Display Modes
 
Old 02-07-2013, 04:36 PM   #1
NewellCrazy
Senior Member
 
NewellCrazy's Avatar
 
Join Date: Sep 2006
Location: Sugarland, TX or Salida,CO
Posts: 1,867
Default Remove and Install EXHAUST MANIFOLD (Water-Cooled) Detroit Diesel 92 Series Engine

This post is strictly for reference material only. Please see the following link for Air-Cooled Engines:

http://www.luxurycoachlifestyle.com/...es-engine.html

See this link for PDF Portion of DD Manual with relation to Exhaust Manifold:

http://www.luxurycoachlifestyle.com/...er-cooled.html

DETROIT DIESEL 92 6.1.1






EXHAUST MANIFOLD (Water-Cooled)




The one-piece water-cooled manifold (Fig. 1) is cast with an integral water jacket surrounding the exhaust chamber. The diameter of the exhaust chamber increases uniformly from one end to the other where it terminates in a flange to which an elbow and flexible exhaust connection is attached. A portion of the engine coolant is bypassed from the rear of the cylinder block into the rear end of the jacket surrounding the exhaust manifold and is discharged from the forward end through a tube into the thermostat housing. A drain cock is installed in the bottom of the manifold for draining the water jacket. A plug is provided in the bottom of the exhaust manifold elbow for draining moisture condensed from the exhaust gases.

First model 8122-7400 marine engines were built with four-bolt design exhaust manifolds, covers, connectors, gaskets and turbo exhaust inlet elbows. This design was replaced by six-bolt design components after a short production run. The six bolt design is now standard on all
12V-92 TA marine engines.

Only the six-bolt design parts and the four-bolt design connector, cover and gasket will be serviced. When a former manifold or turbo exhaust inlet elbow requires replacement, all four-bolt design parts must be replaced by six-bolt design parts.



Remove Exhaust Manifold

Usually, the exhaust manifold will be removed with the cylinder head. However, when the exhaust manifold gasket only needs to be replaced, the manifold may be removed in the following manner without removing the cylinder head:
1. Drain the cooling system.

2. Disconnect the water inlet and the water outlet tubes from the exhaust manifold.

3. Disconnect the exhaust pipe from the flange so that it will not interfere with removal of the exhaust manifold.

4. Loosen and remove the nuts and bevel washers which secure the exhaust manifold to the cylinder head. It is suggested that, as a safeguard, one nut and washer be loosened and left on one of the center studs until all other nuts and washers have been removed.

5. Support the manifold and remove the nut and washer from the center stud.


6. Lift the manifold off the studs and away from the cylinder head.

7. Remove the manifold gasket.

Inspection

Remove the loose scale and carbon that may have accumulated on the internal walls of the exhaust manifold. It is especially important to clean the manifold used on a turbocharged unit to eliminate the possibility of loose scale entering and damaging the turbocharger.

Examine the exhaust manifold studs for damage. If necessary, replace the studs. New studs are driven in to
25-40 lb-ft (34-54 Nem) torque.

Install Exhaust Manifold

With all traces of the old gasket removed from the cylinder head and bolting flange of the exhaust manifold, it may be installed as follows:
1. Make sure the internal walls of the exhaust manifold are clean to eliminate possible damage to the turbocharger, if used.



2. Place a new gasket over the studs and up against the cylinder head.




3. Position the exhaust manifold over the studs and up against the gasket.



NOTICE: Be sure the locating pads on the exhaust manifold rests on the cylinder block locating pads.


















Fig. 1 - Typical Water-Cooled Exhaust Manifold





Detroit Diesel Corporation





6.1.1 Exhaust Manifold (Water Cooled)







4. Install the bevel washers and nuts on the studs and draw the exhaust manifold up against the gasket. Bevel washers should be set in position so that the outer diameter will rest on the manifold and the crown at the center is next to the nut. The exhaust manifold stud nuts should be tightened from the center of the exhaust manifold outward, alternating towards either end. Torque the nuts to 30-35 lb-ft (41-47 Nem).



5. If the exhaust flange was removed from the manifold, install the flange using a new gasket.




6. Connect the exhaust pipe to the flange.




7. Connect the water inlet and outlet tubes to the manifold.



NOTICE: Do not allow exhaust piping to impose excessive loads on the turbocharger.




8. Inspect the exhaust outlet piping for dents, holes and potential sources of water infiltration such as loose clamps or deteriorated seals. Repair or replace, if necessary.




9. Fill the cooling system and check for leaks.

Click image for larger version

Name:	Water Cooled.jpg
Views:	329
Size:	398.5 KB
ID:	3322
__________________
Sean

If Ain't a Newell, It Ain't Wurt Oonin!
NewellCrazy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Testing Lead Acid Batteries The Newell Charging Systems, Electrical & Solar 0 02-25-2013 10:43 PM
Cracked ICE? MrE Off-Topic Discussions & Humor 1 02-25-2013 10:38 PM
Are You an Early Riser? DavidBall Life on the Road | Livin' in Luxury 11 10-30-2012 09:03 PM
South Dakota State Listings TechTalk Northwest 0 08-31-2012 08:03 AM
Do you do ANY of your own Maintenance? fulltiming General Technical Discussion 1 10-16-2007 02:20 PM

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Newell Coach Corporation or any of its affiliates. This is an independent, unofficial site.


All times are GMT. The time now is 09:16 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
×